Pipe transition

Reference ID for this specific instance (e.g. 'WWS/VS1/400/001', which indicates the occurrence belongs to system WWS, subsystems VSI/400, and has the component number 001).

Reference ID for this specified type in this project (e.g. type 'A-1').

Specification clause or section code/reference.

Name of the specification system being used.

Specification clause or section title.

Published version of the classification system.

Subtype of the pipe fitting..The following suggested items should be utilized whenever possible for consistency across applications: BEND_15DEGREE: Changes the direction of flow through 15 degrees. BEND_22_5DEGREE: Changes the direction of flow through 22.5 degrees. BEND_25DEGREE: Changes the direction of flow through 25 degrees. BEND_30DEGREE: Changes the direction of flow through 30 degrees. BEND_45DEGREE: Changes the direction of flow through 45 degrees. BEND_67DEGREE: Changes the direction of flow through 67 degrees. BEND_76DEGREE: Changes the direction of flow through 76 degrees. BEND_87_5DEGREE: Changes the direction of flow through 87.5 degrees. BEND_90DEGREE: Changes the direction of flow through 90 degrees. BEND_135DEGREE: Changes the direction of flow through 135 degrees. BEND_180DEGREE: Changes the direction of flow through 180 degrees. JUNCTION_CROSS_SQUARE: Branch fitting with two opposing branches that are swept in the direction of the main flow. JUNCTION_CROSS_SWEEP: Branch fitting with two swept opposing branches at right angles to the main flow. JUNCTION_TEE_SQUARE: Branch fitting in which the branch is at an angle of 90 degrees to the main pipe. JUNCTION_TEE_SWEEP: Branch fitting in which the branch is curved through 90 degrees to join a main pipe tangentially. JUNCTION_TEE_TWINBEND: Symmetrical pipe fitting in which two short radius bends curve through 90 degree to form a single pipe. +I1JUNCTION_TEE_TWINELBOW: Symmetrical pipe fitting in which two elbows curve through 90 degree to form a single pipe. JUNCTION_TEE_Y: Branch fitting in the shape of a letter Y. OBSTRUCTION_CAP: Device fixed onto the end of a pipe or pipe fitting to close it. OBSTRUCTION_PLUG: Device fixed into the end of a pipe or pipe fitting to close it. OTHER: Other fitting subtype. NOTDEFINED: The fitting subtype is not defined.

Designation of the standard table to which the flange conforms.

Designation of the standard describing the flange table.

Article number or reference that may be applied to a product according to a standard scheme for article number definition (e.g. UN, EAN).

The name of the manufactured item as used by the manufacturer.

The model number and/or unit designator assigned by the manufacturer of the manufactured item.

The identity of the bar code given to an occurrence of the product.

The serial number assigned to an occurrence of a product.

The identity of the batch reference from which an occurrence of a product is taken.

The Global Trade Item Number (GTIN) is an identifier for trade items developed by GS1 (www.gs1.org).

The date that the manufactured item was purchased.

The length or duration of a service life. The lower bound indicates pessimistic service life, the upper bound indicates optimistic service life, and the setpoint indicates the typical service life.

The average time duration between instances of failure of a product.

The identifier assigned to a warranty.

The date on which the warranty commences.

The date on which the warranty expires.

Indication of whether this is an extended warranty whose duration is greater than that normally assigned to an artefact (=TRUE) or not (= FALSE).

The time duration during which a manufacturer or supplier guarantees or warrants the performance of an artefact.

The content of the warranty.

Items, conditions or actions that may be excluded from the warranty or that may cause the warranty to become void.

Date on which the overall condition is assessed.

The overall condition of a product based on an assessment of the contributions to the overall condition made by the various criteria considered. The meanings given to the values of assessed condition should be agreed and documented by local agreements. For instance, is overall condition measured on a scale of 1 - 10 or by assigning names such as Good, OK, Poor.

Qualitative description of the condition.

The name of the person, organisation or library provider that created the object.

URL hyperlink to the object creator’s website.

To record the last date of issue (version or revision) of the object within an object library. Add the date in the following format <yyyymmdd.no> where the ‘no’ suffix is equal to the number of times the object has been issued on that date. For example 20180316.01.

URL hyperlink to the manufacturer’s website.

URL hyperlink to further product information, such as technical documentation or installation guides.

Status of the element, predominately used in renovation or retrofitting projects. The status can be assigned to as "New" - element designed as new addition, "Existing" - element exists and remains, "Demolish" - element existed but is to be demolished, "Temporary" - element will exists only temporary (like a temporary support structure).

The organization that manufactured and/or assembled the item.

Enumeration defining where the assembly is intended to take place, either in a factory or on the building site.

The organization that should be contacted for action under the terms of the warranty. Note that the role of the organization (manufacturer, supplier, installer etc.) is determined by the IfcActorRole attribute of IfcOrganization.

Details of available accessories.

The end-style treatment of the pipe fitting as made available from the manufacturer. If the list contains only one value, then this end-style applies to all ports. For more than one value in the list, the end-style value applies to the port that corresponds to the list index.The following suggested items should be utilized whenever possible for correlation with port enumerations: FLANGED: Flanged. GROOVED: Grooved. THREADED: Threaded. NONE: No end-style has been applied. NOTDEFINED: Undefined end-style type.

TRUE if the fitting has interior duct insulating lining, FALSE if it does not.

Number of boltholes in the flange.

The connection type between pipe segments or fittings and other segments or fittings. If the list contains only one value, then this connection type value applies to all ports. For more than one value in the list, the connection type value applies to the port that corresponds to the list index.The following suggested items should be utilized whenever possible for correlation with port enumerations: BRAZED: Brazed connection type. COMPRESSION: Compression connection type. FLANGED: Flanged connection type including bolts and gasket. GLANDJOINT: Gland-joint connection type. FLEXIBLEBOLTEDGLANDJOINT: Flexible bolted gland-joint connection type. FLEXIBLEBOLTEDGLANDJOINTWITHANODEENDCAP: Flexible bolted gland-joint with anode end-cap connection type. GROOVED: Grooved connection type. SOLDERED: Soldered connection type. SOLDERED_FEMALE: Female-soldered connection type. SOLDERED_MALE: Male-soldered connection type. SWEDGE: Swedge connection type. THREADED: Threaded connection type. THREADED_FEMALE: Female-threaded connection type. THREADED_MALE: Male-threaded connection type. WELDED: Welded connection type. WELDED_BUTT: Butt-welded connection type. WELDED_BRANCH: Branch-welded connection type. WELDED_FLANGE: Flange-welded connection type. NONE: There is no connection. NOTDEFINED: Undefined connection type.

Weight per unit length.

Weight of the pipe fitting itself, not including contained fluid.

Weight of the pipe fitting, including contained fluid as designed.

The pipe fitting material.

Material from which the pipe flange is constructed.

To record any defects found.

The color of the duct fitting. Note: This is typically used for any duct fittings with a painted surface which is not otherwise specified as a covering.

The color of the pipe fitting. Note: This is typically used only for plastic pipe fittings. However, it may be used for any pipe fittings with a painted surface which is not otherwise specified as a covering.

The color of the pipe segment. Note: This is typically used only for plastic pipe segments. However, it may be used for any pipe segments with a painted surface which is not otherwise specified as a covering.

Area of the cross section at the inlet, including the pipe fitting itself and the interior flow space.

Area of the cross section at the inlet, including the pipe fitting and excluding the interior flow space.

Total area of the extruded surfaces of the fitting (not taking into account the end cap areas).

The nominal diameter of the pipe fitting. If the list contains only one value, then this nominal diameter applies to all ports. For more than value in the list, the nominal diameter value applies to the port that corresponds to the list index.

The actual inner diameter of the pipe. Refer to NominalDiameter for comments about interpretation of multiple items in the list.

The actual outer diameter of the pipe. Refer to NominalDiameter for comments about interpretation of multiple items in the list.

The nominal bore of the pipe flange.

Overall diameter of the flange.

Thickness of the material from which the pipe bend is constructed.

Size of the bolts securing the flange.

Diameter of the circle along which the boltholes are placed.

Length of the fitting, calculated at midpoint of cross-section and equal to the distance along the flow path from the port inlet to the port outlet. For junction fittings, it indicates the length of the longest flow path.

Table of sound frequencies and sound power measured in decibels at a reference power of 1 picowatt(10^(-12) watt) for the referenced octave band frequency.

Reference to a database or a classification.

The unit of the quantity the environmental indicators values are related with.

The whole life cycle or only a given phase from which environmental data are valid.

Expected service life in years.

Quantity of energy used as defined in ISO21930:2007.

Quantity of water used.

Quantity of hazardous waste generated.

Quantity of non hazardous waste generated.

Quantity of greenhouse gases emitted calculated in equivalent CO2.

Quantity of gases responsible for the atmospheric acidification calculated in equivalent SO2.

Quantity of renewable energy used as defined in ISO21930:2007.

Quantity of non-renewable energy used as defined in ISO21930:2007.

Quantity of resources used calculated in equivalent antimony.

Quantity of inert waste generated.

Quantity of radioactive waste generated.

Quantity of gases destroying the stratospheric ozone layer calculated in equivalent CFC-R11.

Quantity of gases creating the photochemical ozone calculated in equivalent ethylene.

Quantity of eutrophicating compounds calculated in equivalent PO4.

Quantity of energy used as defined in ISO21930:2007.

Quantity of water used.

Quantity of hazardous waste generated.

Quantity of non hazardous waste generated.

Quantity of greenhouse gases emitted calculated in equivalent CO2.

Quantity of gases responsible for the atmospheric acidification calculated in equivalent SO2.

Quantity of renewable energy used as defined in ISO21930:2007.

Quantity of non-renewable energy used as defined in ISO21930:2007.

Quantity of resources used calculated in equivalent antimony.

Quantity of inert waste generated.

Quantity of radioactive waste generated.

Quantity of gases destroying the stratospheric ozone layer calculated in equivalent CFC-R11.

Quantity of gases creating the photochemical ozone calculated in equivalent ethylene.

Quantity of eutrophicating compounds calculated in equivalent PO4.

Fire rating identifying the entity's fire resistive value (e.g., 1-hour, 2-hour, etc.) so that its resistance to fire can be compared to that of the surrounding structure.

Combustibility (YES it is combustible or NO it is not combustible).

Surface spread of flame characteristics.

The test or rated pressure classification of the fitting.

A factor that determines the pressure loss due to friction through the fitting.

The absolute roughness factor of the duct fitting.

The interior roughness of the pipe fitting material.

The interior roughness coefficient of the pipe segment.

Allowable maximum and minimum temperature.

Allowable maximum and minimum working pressure (relative to ambient pressure).

Dimensionless loss coefficient used for calculating fluid resistance representing the ratio of total pressure loss to velocity pressure at a referenced cross-section.

Leakage flowrate versus pressure difference.

The year of production of the manufactured item.

Lead in time before start of process.

Duration of process.

Lead out time after end of process.